Re: Phaser 6121 driver
The driver has no issue that I just ran here. I can't test much on it since the printer is not sold inside North America, I was able on OSX 10.8-10.10.3 to install without any issue of any kind.ed this...
View ArticleRe: Phaser 3040 - No Yosemite driver.
Drivers get done in an order, this machine was likely left out for a longer time than others due to the fact the 10.9 driver is fully seemingly functional in 10.10 where some other devices 10.10 would...
View ArticleRe: How do you recover a Phaser 8560 after a bad firmware update?
From the first step of the NVRAM reset procedure, I pressed and held the Up arrow button on the Control Panel, and then pressed the OK button, but nothing came up on the display.
View ArticleRe: C75 Operation of Fold/Staple Control Panel Options
Hi TWelton,Thank you for using the Support Forum. Please take a look at the solution for adjusting the SquareFold settings. If this does not help please consider contacting your support centre for...
View ArticlePhaser 7500 cyan streaks
Hello- we use a Phaser 7500. Just replaced the fuser unit, but not imaging units.We are now having 2 blue (cyan) streaks across the top of every page.They appear at about 3/4" and 2" from the top.Have...
View ArticleRe: C75 Square-Fold Trimmer
Not knowing all the facts, I would then try to determine if it is a rip or machine issue by running copy jobs with the trimmer. I'm not sure what 'happens periodically' means. You have to narrow it...
View ArticleRe: C75 Square-Fold Trimmer
The error appears with print jobs, we do virtually no copying on this machine. I am unable to determine a pattern. We can print a short run of 100 booklets and 10 of the 100 will not trim. It can be...
View ArticleMass deploy of workcentre 5335
Hello community! I have issues with the mass deploy of workcentre 5335. I'm trying to do that via Group Policy of Windows Server 2008 R2. I have set in either printer defaults and preferences 1-side...
View ArticleRe: Xerox Phaser 7500 Print Quality Issues (streaks) See Photo
Thank you CherylO ! Following the steps: 1. Print the Troubleshooting Print Quality Page to Help Diagnose a Print Quality Problem I did this first and followed instructions to remove streaks, which...
View ArticlePrint job from multiple trays
I'm a teacher and our school has a Xerox D95/D110/D125 combo. I'm frequently trying to produce packets of printing where the cover page, or maybe pages 5 & 6 of a 12 page packet, are a different...
View ArticleRe: Xerox Phaser 7500 Print Quality Issues (streaks) See Photo
Hi Jason,Since you have tried all the steps and problem continues then yes you will need to call support and potentially need a service call.
View Article6015 not clearing print image
Hi My Workcentre 6015 is no longer clearing the print imageie: it leaves a faint copy of the previous text on what should be blank sections of the page Maybe the drum needs replacing - however, I...
View ArticleClik here to view.
Re: Print job from multiple trays
The answer seems to be yes, if I understand the question.If you are trying to do a mixed media job and the whole job is stapled together as one.Obviously the exact steps change per job and submission...
View ArticleRe: Phaser 7500 cyan streaks
Hi BTP,Thank you for using the Support Forum. Please take a look at the solutions for streaks in cyan and see if any of these will help. If not please consider contacting your support centre for...
View ArticlePhaser 3250DN drops off network after printing one or two pages
I have a Phaser 3250DN printer that has started dropping off the network after switched on and printing one or two pages. If I power cycle the printer, it comes back online, but then drops off the...
View Articlexerox colorqube 9303 PCL errors
We are using GPD PCL driver 5.404.8 and getting frequent print file corruption problems. Causing printer to reboot with PCL error.I have to do a software reset to clear out the bad print jobs. This...
View ArticleRe: Phaser 3250DN drops off network after printing one or two pages
Network drop-offs can occur for a variety of reasons and be triggered by a variety of causes. You may want to make sure you are using the latest software release on the product, as well as check the...
View ArticleXerox docucolor 242 alignement probleme
Hi all I have an alignment problem on my Xerox DocuColor 242 with Fiery System 8e Release 2, the image does not appear centered on the SRA3 45 x 32 cm.I try anything: tray alignment in service mode,...
View ArticleRe: Phaser 3250DN drops off network after printing one or two pages
Hi neilsh Add to SandyP's post with : Switch network cables just to eliminate the most simple thing.Check the web interface of the device right after booting it up if you can get in fast enough and try...
View Article