Hi
I have WC5845i and Phaser 4622 for office printing. The current WC5845i allows uncollated staple function but the P4622 doesn’t like this command and doesn’t uncollated print stapling function. Is there any option to enable uncollated stapling function in phaser 4622.
Your assistance would be highly appreciated.
Thanks in advance.
Bharani
The 4622 has no such option.
You must be looking at the wrong light then.
Right by the fan port near the power cable is a green light about the size of a pencil eraser, that is the one he is referencing.
Also, Follow the attached pdf, it should stop the issue occurring in the future, it only pertains to the 550/560/570 with a Fiery, no other printers.
Hi
I have a Phaser 6022 bought in Nov 2015 via Amazon in the UK. I have just had to replace the yellow cartridge, so bought a genuine Xerox one, again through Amazon in the UK.
However, when I install the new cartridge I get a message "invalid yellow", and the printer will not respond to any of the menu buttons. I returned the cartridge and got a replacement (again, genuine Xerox) and I get the same error message.
I assume Amazon aren't selling fake cartridges (they came in Xerox boxes with a hologram on the side).
Can anyone suggest a solution? Is the printer faulty?
Thanks.
You can't as far as I know, it uses the tray with highest priority.
Copy can have a tray set as the default though.
So it would seem that the priority just needs to change, which is a simple task worth trying. Just try swapping Tray 1 into the first position.
THANK YOU very MUCH, Joe!
I followed your suggestion and set the stock to 155 GSM and so far so good....
I really appreciate the help.
bongcast
Joe. Thank you SO much. The green light was indeed there, I reset the machine using that and followed the instructions in your .pdf and the original IP address info was restored to the printer.
It spit out a config print upon making those changes, which is how I saw that the original IP was restored...so I tested it from my computer and successfully sent a job through to the printer. I did not complete the instructions in the .pdf where it instructs me to use a web browser to make additional changes...things seemed to be working as they were prior to this issue, so I didn't want to ruin my progress by messing with it more.
If you think the rest of those instructions are necessary, please let me know.
I highly suggest it.
This printer, when hooked to a DFE (Fiery or Freeflow) has a terrible habit of doing what your was doing whenever it sleeps for more than 36 hours. So unless you want to deal with it every Monday morning (Assuming 9-5 job Mon-Fri) it should be done.
Hello,
I was wondering if anyone knew if it was okay to show brand logos, i.e. clothing logos, brands on pasta boxes,Brand Advertising Videos, etc. in a monetized video. What you guys think let me know your thoughts. It would be great if you guys help me with your advices.
Any help will be appreciated.
Thank you.
Hi, first post here!
Recently got a Versant 180, loving it, we do a lot of A5 booklets so would like to do them on SRA3 so I can get 2 copies per sheet, on our previous printer I was just doing them on A4 and sending them through the inline finsher, we use an offline Morgana finisher now.
So I would like to do 2 per sheet, then crop them before sending to the finisher.
ANy ideas what the best way is to get 2 copies on the one SRA3 sheet? Going through the booklet maker options only allows for one per sheet, so I have been doing my own impositions in inDesign, but this is time consuming, and as we are getting busier all the time it would be ideal if there was a quicker way.
Hope I'm making some kind of sense!
Many thanks
Hello Joe,
I finally had the time do some tests.
it's broken in the general release of the firmware 73.xx and also in the newer firmware we use (073.200.136.34300),
because it had some fixes for Equitrac. However, the last firmware from July this year, xxx.20500 is working.
Thanks for oiunting me in the right direction.
Wolfgang
Since ythis is not your "first year working as administrator", you might have noticed that you replaced a GDI/host based printer with a proper one, using PCL or PS.
This could mean font policy settings in the driver are involved.
You also didn't mention the OS and printer connection. "cheaper" printers/their driver are often "High-jacking" USB ports, which could
also cause some issues.
Wolfgang
Hello,
I have a Versalink 405 C and it was installed on 4 desktops. From one of them, i cannot print doubleside. I tried from Control Panel\Hardware and Sound\Devices and Printers\Xerox VersaLink C405 PCL6- Adjust print Options- nothing happens when i hit the button " Adjust print options"
I tried from Settings- Add printers and scanners- Xerox Versalink C 405 pcl 6- MANAGE-Nothing happpens when i press the butonns for Printer properties and Printing prefenrences.
I re- installled the drivers- didn't solve the problem.
What can I do next?
Hi Joe,
We are also facing similar issues with 75XX & 57XX families.
Do you have any information which will help on the same ?
Thanks!
Karthik Chandrasekaran
Hi art-gallery,
Thank you for using the Support Forum. Please look at our production machines and use the contact us button to speak with someone about the product that will best meet your needs.
Hi nickbaird,
Thank you for using the Support Forum. Please take a look at this post. I know it is a different machine but the same answer applies. Please consider contacting your support centre for further assistance.
Hi beej1609,
Thank you for using the Support Forum. Please take a look at the solution for creating booklets. If this solutions does not help please consider contacting your support centre for further assistance.
Other steps would be to have a tech re-initialize the nvm's or do an alt boot software load. You may also want to check your power going to the machine is good. Another possibility is that the file is coming over too saturated. see if copies are not fusing as well as other files.
